? semiconductor components industries, llc, 2014 july, 2014 ? rev. 10 1 publication order number: mc14572ub/d mc14572ub hex gate the mc14572ub hex functional gate is constructed with mos p?channel and n?channel enhancement mode devices in a single monolithic structure. these complementary mos logic gates find primary use where low power dissipation and/or high noise immunity is desired. the chip contains four inverters, one nor gate and one nand gate. features ? diode protection on all inputs ? single supply operation ? supply voltage range = 3.0 vdc to 18 vdc ? nor input pin adjacent to v ss pin to simplify use as an inverter ? nand input pin adjacent to v dd pin to simplify use as an inverter ? nor output pin adjacent to inverter input pin for or application ? nand output pin adjacent to inverter input pin for and application ? capable of driving two low?power ttl loads or one low?power schottky ttl load over the rated temperature range ? nlv prefix for automotive and other applications requiring unique site and control change requirements; aec?q100 qualified and ppap capable* ? this device is pb?free and is rohs compliant maximum ratings (voltages referenced to v ss ) parameter symbol value unit dc supply voltage range v dd ?0.5 to +18.0 v input or output voltage range (dc or transient) v in , v out ?0.5 to v dd + 0.5 v input or output current (dc or transient) per pin i in , i out 10 ma power dissipation, per package (note 1) p d 500 mw ambient temperature range t a ?55 to +125 c storage temperature range t stg ?65 to +150 c lead temperature (8?second soldering) t l 260 c stresses exceeding those listed in the maximum ratings table may damage the device. if any of these limits are exceeded, device functionality should not be assumed, damage may occur and reliability may be affected. 1. temperature derating: ?d/dw? package: ?7.0 mw/ c from 65 c to 125 c this device contains protection circuitry to guard against damage due to high static voltages or electric fields. however, precautions must be taken to avoid applications of any voltage higher than maximum rated voltages to this high?impedance circuit. for proper operation, v in and v out should be constrained to the range v ss (v in or v out ) v dd . unused inputs must always be tied to an appropriate logic voltage level (e.g., either v ss or v dd ). unused outputs must be left open. device package shipping ? ordering information http://onsemi.com mc14572ubdr2g soic?16 (pb?free) 2500/tape & ree l mc14572ubdg soic?16 (pb?free) 48 units / rail a = assembly location wl = wafer lot yy = year ww = work week g = pb?free package marking diagram soic?16 d suffix case 751b 1 16 14572ug awlyww 1 nlv14572ubdr2g* soic?16 (pb?free) 2500/tape & ree l ?for information on tape and reel specifications, including part orientation and tape sizes, please refer to our t ape and reel packaging specification s brochure, brd8011/d. pin assignment 13 14 15 16 9 10 11 12 5 4 3 2 1 8 7 6 in e out f in 1 f in 2 f v dd out d in d out e in b out b in a out a v ss in 2 c in 1 c out c
mc14572ub http://onsemi.com 2 logic diagram 15 14 12 10 7 6 4 2 13 11 9 5 3 1 v dd = pin 16 v ss = pin 8 circuit schematic v dd v dd v dd 2 7 6 1 5 14 15 13 v ss v ss v ss
mc14572ub http://onsemi.com 3 electrical characteristics (voltages referenced to v ss ) characteristic symbo l v dd vdc ? 55 c 25 c 125 c unit min max min typ (note 2) max min max output voltage ?0? level v in = v dd or 0 v ol 5.0 10 15 ? ? ? 0.05 0.05 0.05 ? ? ? 0 0 0 0.05 0.05 0.05 ? ? ? 0.05 0.05 0.05 vdc v in = 0 or v dd ?1? level v oh 5.0 10 15 4.95 9.95 14.95 ? ? ? 4.95 9.95 14.95 5.0 10 15 ? ? ? 4.95 9.95 14.95 ? ? ? vdc input voltage ?0? level (v o = 4.5 or 0.5 vdc) (v o = 9.0 or 1.0 vdc) (v o = 13.5 or 1.5 vdc) v il 5.0 10 15 ? ? ? 1.0 2.0 2.5 ? ? ? 2.25 4.50 6.75 1.0 2.0 2.5 ? ? ? 1.0 2.0 2.5 vdc ?1? level (v o = 0.5 or 4.5 vdc) (v o = 1.0 or 9.0 vdc) (v o = 1.5 or 13.5 vdc) v ih 5.0 10 15 4.0 8.0 12.5 ? ? ? 4.0 8.0 12.5 2.75 5.50 8.25 ? ? ? 4.0 8.0 12.5 ? ? ? vdc output drive current (v oh = 2.5 vdc) source (v oh = 4.6 vdc) (v oh = 9.5 vdc) (v oh = 13.5 vdc) i oh 5.0 5.0 10 15 ?1.2 ?0.25 ?0.62 ?1.8 ? ? ? ? ?1.0 ?0.2 ?0.5 ?1.5 ?1.7 ?0.36 ?0.9 ?3.5 ? ? ? ? ?0.7 ?0.14 ?0.35 ?1.1 ? ? ? ? madc (v ol = 0.4 vdc) sink (v ol = 0.5 vdc) (v ol = 1.5 vdc) i ol 5.0 10 15 0.64 1.6 4.2 ? ? ? 0.51 1.3 3.4 0.88 2.25 8.8 ? ? ? 0.36 0.9 2.4 ? ? ? madc input current i in 15 ? 0.1 ? 0.00001 0.1 ? 1.0 adc input capacitance (v in = 0) c in ? ? ? ? 5.0 7.5 ? ? pf quiescent current (per package) i dd 5.0 10 15 ? ? ? 0.25 0.5 1.0 ? ? ? 0.0005 0.0010 0.0015 0.25 0.5 1.0 ? ? ? 7.5 15 30 adc total supply current (notes 3, 4) (dynamic plus quiescent, per package) (c l = 50 pf on all outputs, all buffers switching) i t 5.0 10 15 i t = (1.89 a/khz) f + i dd i t = (3.80 a/khz) f + i dd i t = (5.68 a/khz) f + i dd adc product parametric performance is indicated in the electrical characteristics for the listed test conditions, unless otherwise noted. product performance may not be indicated by the electrical characteristics if operated under different conditions. 2. data labelled ?typ? is not to be used for design purposes but is intended as an indication of the ic?s potential performance. 3. the formulas given are for the typical characteristics only at 25 c. 4. to calculate total supply current at loads other than 50 pf: i t (c l ) = i t (50 pf) + (c l ? 50) vfk where: i t is in a (per package), c l in pf, v = (v dd ? v ss ) in volts, f in khz is input frequency, and k = 0.006.
mc14572ub http://onsemi.com 4 switching characteristics (type 5) (c l = 50 pf, t a = 25 c) characteristic symbol v dd min typ (note 6) max unit output rise time t tlh = (3.0 ns/pf) c l + 30 ns t tlh = (1.5 ns/pf) c l + 15 ns t tlh = (1.1 ns/pf) c l + 10 ns t tlh 5.0 10 15 ? ? ? 180 90 65 360 180 130 ns output fall time t thl = (1.5 ns/pf) c l + 25 ns t thl = (0.75 ns/pf) c l + 12.5 ns t thl = (0.55 ns/pf) c l + 9.5 ns t thl 5.0 10 15 ? ? ? 100 50 40 200 100 80 ns propagation delay time t plh , t phl = (1.7 ns/pf) c l + 5 ns t plh , t phl = (0.66 ns/pf) c l + 17 ns t plh , t phl = (0.5 ns/pf) c l + 15 ns t plh , t phl 5.0 10 15 ? ? ? 90 50 40 180 100 80 ns 5. the formulas given are for the typical characteristics only at 25 c. 6. data labelled ?typ? is not to be used for design purposes but is intended as an indication of the ic?s potential performance. figure 1. switching time test circuits and waveforms pulse generator pulse generator input 2 input 15 v dd v dd 16 16 8 8v ss v ss c l c l 1 13 output output pulse generator input 7 v dd 16 5 output 8v ss c l 6 20 ns 20 ns v dd v ss v oh v ol t r t f 90% 50% 10% 90% 50% 10% 90% 50% 10% 90% 10% 50% input output t phl t plh 14
mc14572ub http://onsemi.com 5 package dimensions soic?16 case 751b?05 issue k notes: 1. dimensioning and tolerancing per ansi y14.5m, 1982. 2. controlling dimension: millimeter. 3. dimensions a and b do not include mold protrusion. 4. maximum mold protrusion 0.15 (0.006) per side. 5. dimension d does not include dambar protrusion. allowable dambar protrusion shall be 0.127 (0.005) total in excess of the d dimension at maximum material condition. 18 16 9 seating plane f j m r x 45 g 8 pl p ?b? ?a? m 0.25 (0.010) b s ?t? d k c 16 pl s b m 0.25 (0.010) a s t dim min max min max inches millimeters a 9.80 10.00 0.386 0.393 b 3.80 4.00 0.150 0.157 c 1.35 1.75 0.054 0.068 d 0.35 0.49 0.014 0.019 f 0.40 1.25 0.016 0.049 g 1.27 bsc 0.050 bsc j 0.19 0.25 0.008 0.009 k 0.10 0.25 0.004 0.009 m 0 7 0 7 p 5.80 6.20 0.229 0.244 r 0.25 0.50 0.010 0.019 6.40 16x 0.58 16x 1.12 1.27 dimensions: millimeters 1 pitch soldering footprint 16 89 8x on semiconductor and the are registered trademarks of semiconductor components industries, llc (scillc) or its subsidia ries in the united states and/or other countries. scillc owns the rights to a number of pa tents, trademarks, copyrights, trade secret s, and other intellectual property. a listin g of scillc?s product/patent coverage may be accessed at www.onsemi.com/site/pdf/patent?marking.pdf. scillc reserves the right to make changes without further notice to any product s herein. scillc makes no warranty, representation or guarantee regarding the suitability of its products for any part icular purpose, nor does sci llc assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. ?typi cal? parameters which may be provided in scillc data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. all operating param eters, including ?typicals? must be validated for each customer application by customer?s technical experts. scillc does not convey any license under its patent rights nor the right s of others. scillc products are not designed, intended, or authorized for use as components in systems intended for surgic al implant into the body, or other applications intended to s upport or sustain life, or for any other application in which the failure of the scillc product could create a situation where personal injury or death may occur. should buyer purchase or use scillc products for any such unintended or unauthorized application, buyer shall indemni fy and hold scillc and its officers, em ployees, subsidiaries, affiliates, and dist ributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that scillc was negligent regarding the design or manufac ture of the part. scillc is an equal opportunity/affirmative action employer. this literature is subject to all applicable copyright laws and is not for resale in any manner. p ublication ordering information n. american technical support : 800?282?9855 toll free usa/canada europe, middle east and africa technical support: phone: 421 33 790 2910 japan customer focus center phone: 81?3?5817?1050 mc14572ub/d literature fulfillment : literature distribution center for on semiconductor p.o. box 5163, denver, colorado 80217 usa phone : 303?675?2175 or 800?344?3860 toll free usa/canada fax : 303?675?2176 or 800?344?3867 toll free usa/canada email : orderlit@onsemi.com on semiconductor website : www.onsemi.com order literature : http://www.onsemi.com/orderlit for additional information, please contact your loc al sales representative
|
